Tuffy-security 292 User Manual download pdf

Page 1 of 2 – 12/29/2011 – Rev 4/20/12

INSTALLATION INSTRUCTIONS

JEEP 2007-Current JK Hood Lock #292

Call (970) 564-1762 for Technical Support

Please read and fill out the enclosed warranty registration card to activate your warranty.

PARTS CHECKLIST SHIPPING PACKAGE CHECKLIST

#1 Hood Lock #3.1 - (2) 5/16-18 x 1/2”

THREAD CUTTING BOLTS

#3.2 - (2) 5/16-18 x 1/2”

BOLTS

TOOLS NEEDED

• ½” socket and wrench

• Body Trim tool

ATTENTION:

• THIS HOOD LOCK WAS DESIGNED FOR A STOCK OEM VEHICLE, ANY MODIFICATIONS MADE TO

THE GRILLE, RADIATOR, ETC MAY AFFECT THE FIT.

PLEASE READ ALL INSTRUCTIONS THOROUGHLY BEFORE STARTING INSTALLATION.

1. IMPORTANT! Make sure the vehicle is parked on a flat surface, placed in park, and the emergency brake is

activated.

2. Raise the vehicle hood. Using a body trim tool, pry up the center head on each of the (6) OEM push-pin retainers

along the top of the #4.2 OEM plastic grille, and remove the (6) push-pin retainers. Pulling the grille carefully but

firmly forward, un-clip the (6) OEM metal spring clips along the bottom of the grille. **UNPLUG THE OEM TURN

SIGNAL/MARKER LIGHTS ON BOTH SIDES OF THE VEHICLE. Remove the grille from the vehicle. Refer to your

vehicles factory service manual for additional instructions on removing the OEM grille.

3. Using a body trim tool, pry the (2) push-pin retainers near the center of the radiator bar which are supporting the OEM

wire harness to the #4.1 OEM radiator support. This will facilitate the installation of the #1 Hood Lock.

4. Install the #3.1 Thread Cutting Bolts in the pre-existing (2) mounting holes along the top of the #4.1 OEM radiator

support. This will cut the threads for these holes. Remove the #3.1 Thread Cutting Bolts.

**NOTE: DO NOT OVER TIGHTEN THE BOLTS OR YOU MIGHT STRIP THE THREADS WHICH WERE CUT INTO

THE #4.1 RADIATOR SUPPORT.

5. Install the #1 Hood Lock onto the #4.1 OEM radiator support and fasten at the front mounting holes with the #3.1

Thread Cutting Bolts. Tighten fasteners. (Figure 1)

6. Install the #3.2 bolts into the top mounting holes in the #1 Hood Lock and the threaded holes in the #4.1 radiator

support. Tighten fasteners. (Figure 1) **BE SURE TO USE THE #3.2 BOLTS AT THE TOP OF THE RADIATOR

SUPPORT FOR CLEARANCE TO THE #4.2 OEM GRILLE.

7. With the #1 Hood Lock in the un-locked position (key turned counter-clockwise), lower the vehicle hood and allow the

#4.3 OEM hood latch to engage the #4.1 radiator support. Lock the #1 Hood Lock (turn key clockwise) and test the

lock has engaged the #4.3 hood latch securely by pulling firmly up on the vehicle hood. You should not be able to lift

the vehicle hood. Unlock and raise the hood again.

1 2

ATTENTION: 1
FIGURE 1 2

Summary of Contents

Page 1 - ATTENTION:

Page 1 of 2 – 12/29/2011 – Rev 4/20/12 INSTALLATION INSTRUCTIONS JEEP 2007-Current JK Hood Lock #292 Call (970) 564-1762 for Technical Support Pleas

Page 2 - FIGURE 1

Page 2 of 2 – 12/29/2011 – Rev 4/20/12 **Note: It may be necessary to push the vehicle hood downward when locking the #1 Hood Lock in order for the lo

Comments to this Manuals

No comments

Tuffy-security 292 User Manual

Browse online or download User Manual for For the car Tuffy-security 292. Tuffy Security 292 User Manual [en]

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Tuffy-security 292