Tuffy-security 257 User Manual download pdf

Page 1 of 3 – 12/28/2010 – Rev12/28/2010

INSTALLATION INSTRUCTIONS

Large Truck Multi-Drawer (Exterior

Use) – Part #257

Enclosure Drawers (Qty per Custom Order)

Shipping Package

#35.14 (7) 3/8”-16x1 3/4” Bolts #35.13 (14) 3/8” Washers #35.12 (7) 3/8”-16 Nuts

Tools required

 9/16” Shallow socket with a long extension and a ratchet (Universal joint also helps)

 9/16” Wrench

 Drill and 3/8” drill bit (Optional for additional security)

Mounting Directions

WARNING! These drawers are rated to hold a maximum of 400# evenly distributed. The enclosure is rated to

hold 2000# on top evenly distributed. This would include any dividers mounted in the drawer. Never stand or sit

on the Tuffy drawers or enclosure. The vehicle should not be operated with the drawer(s) opened and not

secured shut. The drawers should not be operated/opened when not level. Keep hands clear of moving parts

and pinch points when maneuvering the drawers. Do not exceed the rated weight capacity for this product.

FOR SAFETY THE DRAWER REMOVAL REQUIRES AT LEAST (2) PEOPLE. THE DRAWERS SHOULD ALWAYS

BE EMPTY BEFORE REMOVING IT. CONSTANT SUPPORT MUST BE APPLIED TO HOLD UP THE FRONT OF THE

DRAWERS THROUGHOUT THE ENTIRE REMOVAL PROCESS SO IT DOES NOT CAUSE INJURY AND/OR

DAMAGE.

1. Check the truck bed and wheel well panels of the vehicle for cubby holes containing important gear or require access

in an emergency (Jack, spare tire, spare tire access, fuses, etc.). Remove and relocate any inaccessible items as

required.

2. Remove drawers from enclosure. Pull each drawer out until it stops. Lift up the front of the drawer and pull it out a

few inches further until the stop bolts on the drawer slides clear the rollers on the enclosure slide. Pull the drawer

again until it stops being sure to support the front of the drawer. Pivot the front of the drawer down and lift the rear

end of the drawer out so the rollers on the drawer slides pull free through the slots in the enclosure slides. Repeat for

the remaining drawer(s). Reverse steps to install. (See Figure 1)

FIGURE 1

QC CHECK

 VISUAL INSPECTION

 BEARING INSPECTION

 SLIDE TEST

 DRAWER STOP

 RUBBER SEAL

 CORRECT KEY (& COMBO

SETTING)

 PUSHBUTTON LOCK TEST

 COMBO LOCK TEST (IF INCL)

 LATCH TEST

 SHIPPING PACKAGE

 DIVIDERS (IF INCL)

 TRIM KIT (IF INCL)

 MOUNTING KITS (IF INCL)

 VERIFY CROSS BRACES

 UNLOCKED WITH KEY INSIDE

QC INSPECTOR INITIALS ____________

1 2 3

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

Page 1 of 3 – 12/28/2010 – Rev12/28/2010 INSTALLATION INSTRUCTIONS Large Truck Multi-Drawer (Exterior Use) – Part #257 Enclosure Drawers

Page 2 - ATTENTION:

Page 2 of 3 – 12/28/2010 – Rev12/28/2010 3. Place the drawer enclosure in the vehicle in the desired mounting location and mark where the (6) side

Page 3 - Figure 4

Page 3 of 3 – 12/28/2010 – Rev12/28/2010  If the latch handle is removed or has been bumped out of alignment it will need to be adjusted correctly a

Comments to this Manuals

No comments

Tuffy-security 257 User Manual

Browse online or download User Manual for For the car Tuffy-security 257. Tuffy Security 257 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Tuffy-security 257